 |
Update 05/31/2022 Effective May 31st PixRacer Pro will be using Bosch BMI085.
Notice:
The COVID-19 pandemic and disruption of the worldwide silicon chip manufacturing industry have caused increased delays and prices of most electronic components. We have experienced some price increases of 4x or more. Because of this, we are forced to raise prices on some of our products.Lead times are less predictable, and mRobotics prioritize orders for established customers, the medical industry, and national defense. If you have a specific need, please get in touch with us and we will do all we can to accommodate you.
Thank you for your continued support. For quotes on large orders and lead times, please send your inquiry to help@mrobotics.io or call us at 619-503-1003. Four years after the original Pixracer was designed and proven, we recognized the need to bring the design to the forefront of open-source flight controllers. With the Pixracer Pro, we maintained everything that the UAV community loved about the original Pixracer and improved every deficiency that was known. The resulting model is destined to become the new go-to flight controller for developers and will provide a rock solid foundation for commercial and industrial systems.
Please visit our docs site for more information.
Main Processor: 32-bit STM32H743IIK6 Cortex M7 RISC core with FPU 460 MHz IO Processor: No RAM: 1024 KB RAM Flash: 2 MB FRAM Crypto / Hash Processor: No Accelerometers / Gyros / Mags: Yes Sensors: Invensense/TDK ICM-20602 (6DOF) Invensense/TDK ICM-20948 (9DOF) Sensors - Dampened: Bosch BMI085 (6DOF) (internally vibration dampened) Internal Magnetometer: AK09916 inside ICM-20948 Barometric Pressure Sensor: DPS310 Interfaces and Protocols: 6x UART (serial ports) [2x with HW flow control,1x FRSky Telemetry (D or X types), 2x General Purpose & 1x GPS+I2C 1x PPM sum input signal 8x PWM outputs (all DShot capable) 1x RSSI (PWM or voltage) input 1x I2C 1x SPI 2x CAN 1x JTAG (TC2030 Connector) 3x Ultra low noise LDO voltage regulator Supported RC input protocols: Spektrum DSM / DSM2 / DSM-X® Satellite compatible input and binding. Futaba S.BUS® & S.BUS2® compatible input. FRSky Telemetry port output. Graupner SUMD.Yuneec ST24. Connectors: -JST GH -External USB-C
Pin Headers: Yes - 8 Servo * pins are not soldered Conformal Coating: No Extended Testing and Burn In: No Custom Carrier Board Support: No LED: Yes (Tricolor)
Dimensions: Width: 36mm (1.42”) / Length: 36mm (1.42”) Weight: 9.09g (.31 oz) w/o pins Mounting Holes: 4mm holes at 30.5mm spacing, Silicone grommets for m3 screws Protector Case: No Typical Platforms: -Multirotor -Rover -Fixed-Wing -Boats -Submarines -VTOL -Automatic Tractors -Others
Compatibility: Ardupilot, PX4
[Made in USA]
- 1x SD Card
- 1x USB C Cable
- 1x Right angle pin 3x8
- 1x Connector GH Housing 8 position 1.25 mm
- 2x Connector GH Housing 6 position 1.25 mm
- 4x Rubber Balls (Dampers)
- 1x Heatsink
- 2x MRC0206 mRo 6-Pins JST-GH to 6-Pins JST-GH
- 1x MRC0202 mRo 6-Pins JST-GH to 6 Separate 2.54mm Females
- 1x MRC0204 mRo 5-Pins JST-GH to 3-Pins Servo and 3-Pins JST-ZHR and 1-Pin (2.54mm) Female
- 1x MRC0205 mRo 4-Pins JST-GH to 4-Pins JST-GH
- 1x MRC0287 mRo 8-Pin JST-GH to 8PCS Dupont 1Pin Connector
- 1x MRC0288 mRo 8-Pin JST-GH to 2PCS JST-GH 4Pin Connector
|
|
 |