Some shipments may be delayed due to the ongoing supply chain disruptions and chip manufacturing shortages caused by the pandemic.

 If you have an order or shipping question please contact us at Thank you for your continued support.

  Home > All >

mRo Pixhawk 2.4.6 Essential Kit!
mRo Pixhawk 2.4.6 Essential Kit!

Alternative Views:

Our Price: $289.90
Harmonized Tariff Code: 9014.80.4000
ECCN: 7A994

Quantity in Stock:(Out of Stock)

Availability:: Discontinued Replaced by mRo Control Zero Classic

Power Module*:
mRo Classic Power Module (BEC) w/ Adapter [Add $20.00]
Nah! Thanks...

The mRo Pixhawk flight controller is nearing retirement and we are reaching the end of our general stock. We encourage you to explore our newer, more advanced, and powerful flight controller options. If you absolutely need to purchase this model, please contact us for a custom production quotation.
Pixhawk is replaced by mRo Control Zero Classic

For quotes on large orders and lead times, please send your enquiry to or call us at 619-503-1003.

Warning gorilla hands: DF13 connectors are extremely fragile. mRo has reinforced most of them by adding vias under the pads, this will act as "anchors" making them a little stronger. Still, some pads like the one used by the Buzzer connector cannot be reinforced due to the signal density below it. You should never use more force than the one required to flip your home-wall light switch. You can find several videos on YouTube that explain how to remove it. Note that if you break it, mRo will not replace it.

Time tested, extremely robust genuine PixHawk 1 is back.

This Pixhawk has a few improvement that never made it to the public, including STM32F427 revision 3 that corrects a bug that limited the Pixhawk to 1MB of flash. Note that most of the original PixHawks do not have rev. 3. It was not available at the time they were produced, make sure to ask before buying.


1 x SanDisk Ultra micro SD Card (8GB).
1 x MRC0225- Cable [3-Pins DF-13] to Switch+LED.
1 x MRC0224- Cable [2-Pins DF-13] to Buzzer.
1 x I2C Splitter.
2 x MRC0213- Cable [6-Pins JST-GH] to [6-Pins DF-13], (Telemetry Radio, Power module and Extra).
1 x MRC0216- Cable [6-Pins DF-13] to [6-Pins DF-13], (For legacy products).
4 x Damping Foams.
3 x Decals "APM Rover", "APM Copter" and "APM Plane".


Advanced 32 bit ARM Cortex® M4 Processor running NuttX RTOS
14 PWM/servo outputs (8 with failsafe and manual override, 6 auxiliary, high-power compatible)
Abundant connectivity options for additional peripherals (UART, I2C, CAN)
Integrated backup system for in-flight recovery and manual override with dedicated processor and stand-alone power supply
Backup system integrates mixing, providing consistent autopilot and manual override mixing modes
Redundant power supply inputs and automatic failover
External safety button for easy motor activation
Multicolor LED indicator
High-power, multi-tone piezo audio indicator
microSD card for long-time high-rate logging


PPM encoder for RC receivers that do not provide PPM output. [Coming soon]
u-blox GPS with compass (required for autonomous flight). [Coming soon]


32-bit STM32F427 Cortex M4 core with FPU
168 MHz/256 KB RAM/2 MB Flash
32 bit STM32F103 failsafe co-processor
ST Micro L3GD20 3-axis 16-bit gyroscope
ST Micro LSM303D 3-axis 14-bit accelerometer / magnetometer
Invensense MPU 6000 3-axis accelerometer/gyroscope
MEAS MS5611 barometer
5x UART (serial ports), one high-power capable, 2x with HW flow control
2x CAN
Spektrum DSM / DSM2 / DSM-X® Satellite compatible input up to DX8 (DX9 and above not supported)
Futaba S.BUS® compatible input and output
PPM sum signal
RSSI (PWM or voltage) input
3.3 and 6.6V ADC inputs
External microUSB port
Power System:
Ideal diode controller with automatic failover
Servo rail high-power (7 V) and high-current ready
All peripheral outputs over-current protected, all inputs ESD protected

Weight and Dimensions:

Weight: 38g (1.31oz)
Width: 50mm (1.96")
Thickness: 15.5mm (.613")
Length: 81.5mm (3.21")

[Made in USA]

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 1 Write a review »

  0 of 0 people found the following review helpful:
5 of 5 European distributor? December 4, 2016
Reviewer: Johhan Stew from Einhdoven, Einhdoven Netherlands  
Hi guys, I am really interested in your products (and mainly in this Pixhawk Kit) but I will be charger with imports fees here in Netherlands. Is there shop on this side of the Atlantic where I can buy from? Thanks for all

Was this review helpful to you?