Home > All >

mRo Pixhawk 2.4.6 Cool Kit! (Limited edition)
mRo Pixhawk 2.4.6 Cool Kit! (Limited edition)


 
Alternative Views:


Our Price: $259.90
Harmonized Tariff Code: 9014.80.4000
ECCN: 7A994


Availability:: ***Pre-Order NOW*** Usually Ships in 3 to 4 Weeks
Product Code: MRO-PIXHAWK1-FULLKIT-MR

Radio Frequency:

SiK Radio 433MHz Info
SiK Radio 915MHz Info
PixHawk GPS Options:

M8N + (LIS3MDL + IST8310) Info

Qty:  
Description
 
[Assembled & Tested in California]

Warning gorilla hands: DF13 connectors are extremely fragile. mRo has reinforced most of them by adding vias under the pads, this will act as "anchors" making them a little stronger. Still, some pads like the one used by the Buzzer connector cannot be reinforced due to the signal density below it. You should never use more force than the one required to flip your home-wall light switch. You can find several videos on YouTube that explain how to remove it. Note that if you brake it, mRo will not replace it.

Limited edition 'Cool' Kit with Free 915MHz/433MHz Telemetry Radios (While supply lasts)!

Time tested, extremely robust genuine PixHawk 1 is back!!.

This Pixhawk has a few improvement that never made it to the public, including STM32F427 revision 3 that corrects a bug that limited the Pixhawk to 1MB of flash. Note that most of the original PixHawks do not have rev. 3. It was not available at the time they were produced, make sure to ask before buying.

Includes:
1 x Signature mRo U-Blox M8N GPS.
1 x Telemetry 915MHz or 433MHz (Two radios).
2 x 915Mhz or 433Mhz SMA Antennas.
1 x Classic mRo BEC (Power Module) w/ Cable Adapter 150mm.
1 x SanDisk Ultra micro SD Card (8GB).
1 x MRC0225- Cable [3-Pins DF-13] to Switch+LED.
1 x MRC0224- Cable [2-Pins DF-13] to Buzzer.
1 x I2C Splitter.
2 x MRC0213- Cable [6-Pins JST-GH] to [6-Pins DF-13], (Telemetry Radio, Power module and Extra).
1 x MRC0202- Cable [6-Pins JST-GH] to [Single 2.54mm Female Header Connector], (For OSD, Testing, Hacking).
1 x MRC0216- Cable [6-Pins DF-13] to [6-Pins DF-13], (For legacy products).
1 x MRC0200- Cable [6-Pins JST-GH] to [6-Pins DF-13] & [4-Pins DF-13], 200mm (To adapt new GPS + Mags).
4 x Damping Foams.
3 x Decals "APM Rover", "APM Copter" and "APM Plane".


Features

Advanced 32 bit ARM Cortex® M4 Processor running NuttX RTOS
14 PWM/servo outputs (8 with failsafe and manual override, 6 auxiliary, high-power compatible)
Abundant connectivity options for additional peripherals (UART, I2C, CAN)
Integrated backup system for in-flight recovery and manual override with dedicated processor and stand-alone power supply
Backup system integrates mixing, providing consistent autopilot and manual override mixing modes
Redundant power supply inputs and automatic failover
External safety button for easy motor activation
Multicolor LED indicator
High-power, multi-tone piezo audio indicator
microSD card for long-time high-rate logging

Options:

PPM encoder for RC receivers that do not provide PPM output.
u-blox GPS with compass (required for autonomous flight).

Specifications:

Microprocessor:
32-bit STM32F427 Cortex M4 core with FPU
168 MHz/256 KB RAM/2 MB Flash
32 bit STM32F103 failsafe co-processor
Sensors:
ST Micro L3GD20 3-axis 16-bit gyroscope
ST Micro LSM303D 3-axis 14-bit accelerometer / magnetometer
Invensense MPU 6000 3-axis accelerometer/gyroscope
MEAS MS5611 barometer
Interfaces:
5x UART (serial ports), one high-power capable, 2x with HW flow control
2x CAN
Spektrum DSM / DSM2 / DSM-X® Satellite compatible input up to DX8 (DX9 and above not supported)
Futaba S.BUS® compatible input and output
PPM sum signal
RSSI (PWM or voltage) input
I2C®
SPI
3.3 and 6.6V ADC inputs
External microUSB port
Power System:
Ideal diode controller with automatic failover
Servo rail high-power (7 V) and high-current ready
All peripheral outputs over-current protected, all inputs ESD protected

Weight and Dimensions:

Weight: 38g (1.31oz)
Width: 50mm (1.96")
Thickness: 15.5mm (.613")
Length: 81.5mm (3.21")

Share your knowledge of this product. Be the first to write a review »