Notice:
Some shipments may be delayed due to the ongoing supply chain disruptions and chip manufacturing shortages caused by the pandemic.

 If you have an order or shipping question please contact us at help@mrobotics.io. Thank you for your continued support.


  Home > All >

mRo Pixhawk 2.4.6 Essential Kit
mRo Pixhawk 2.4.6 Essential Kit


 
Alternative Views:


Our Price: $289.90
Harmonized Tariff Code: 9014.80.4000
ECCN: 7A994

Quantity in Stock:(Out of Stock)

Availability:: Discontinued Replaced by mRo Control Zero Classic
Product Code: MRO-PIXHAWK1-MINKIT-MR


Power Module*:
mRo Classic Power Module (BEC) w/ Adapter [Add $20.00]
Nah! Thanks...

Qty:  
Description
 
For quotes on large orders and lead times, please send your inquiry to help@mrobotics.io or call us at 619-503-1003.

The mRo Pixhawk flight controller is nearing retirement and we are reaching the end of our general stock. We encourage you to explore our newer, more advanced, and powerful flight controller options. If you absolutely need to purchase this model, please contact us for a custom production quotation.

*Pixhawk has been replaced by mRo Control Zero Classic*

Warning gorilla hands: DF13 connectors are extremely fragile. mRo has reinforced most of them by adding vias under the pads; these will act as "anchors", making them a little stronger. Still, some pads, like the one used by the Buzzer connector, cannot be reinforced due to the signal density below it. You should never use more force than that required to flip your home wall light switch. You can find several videos on YouTube that explain how to remove it. Note that if you break it, mRo will not replace it.

Time-tested, extremely robust Pixhawk 1 is back. This Pixhawk has a few improvements that never made it to the public, including STM32F427 revision 3 that corrects a bug that limited the Pixhawk to 1MB of flash. Note that most of the original Pixhawks do not have revision 3, for it was not available at the time they were produced; make sure to ask before buying.

Includes:
-1 x SanDisk Ultra micro SD Card (8GB)
-1 x MRC0225 - Cable [3-Pin DF-13] to Switch+LED
-1 x MRC0224 - Cable [2-Pin DF-13] to Buzzer
-1 x I²C Splitter
-2 x MRC0213 - Cable [6-Pin JST-GH] to [6-Pin DF-13], (Telemetry Radio, Power module, and Extra)
-1 x MRC0216 - Cable [6-Pin DF-13] to [6-Pin DF-13] (for legacy products)
-4 x Damping Foams
-3 x Decals "APM Rover", "APM Copter", and "APM Plane"

Features:
-Advanced 32 bit ARM Cortex® M4 Processor running NuttX RTOS
-14 PWM/servo outputs (8 with failsafe and manual override, 6 auxiliary, high-power compatible)
-Abundant connectivity options for additional peripherals (UART, I2C, CAN)
-Integrated backup system for in-flight recovery and manual override with dedicated processor and stand-alone power supply
-Backup system integrates mixing, providing consistent autopilot and manual override mixing modes
-Redundant power supply inputs and automatic failover
-External safety button for easy motor activation
-Multicolor LED indicator
-High-power, multi-tone piezo audio indicator
-microSD card for long-time high-rate logging

Options:
-PPM encoder for RC receivers that do not provide PPM output [Coming soon]
-u-blox GPS with compass (required for autonomous flight) [Coming soon]

Specifications:
Microprocessor:
-32-bit STM32F427 Cortex M4 core with FPU
-168 MHz/256 KB RAM/2 MB Flash
-32 bit STM32F103 failsafe co-processor
Sensors:
-ST Micro L3GD20 3-axis 16-bit gyroscope
-ST Micro LSM303D 3-axis 14-bit accelerometer / magnetometer
-Invensense MPU 6000 3-axis accelerometer/gyroscope
-MEAS MS5611 barometer
Interfaces:
-5x UART (serial ports), one high-power capable, 2x with HW flow control
-2x CAN
-Spektrum DSM / DSM2 / DSM-X® Satellite compatible input up to DX8 (DX9 and above not supported)
-Futaba S.BUS® compatible input and output
-PPM sum signal
-RSSI (PWM or voltage) input
-I²C®
-SPI
-3.3 and 6.6V ADC inputs
-External microUSB port
Power System:
-Ideal diode controller with automatic failover
-Servo rail high-power (7 V) and high-current ready
-All peripheral outputs over-current protected, all inputs ESD protected

Weight and Dimensions:
Weight: 38g (1.31oz)
Width: 50mm (1.96")
Thickness: 15.5mm (.613")
Length: 81.5mm (3.21")

[Made in USA]

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 1 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 European distributor? December 4, 2016
Reviewer: Johhan Stew from Einhdoven, Einhdoven Netherlands  
Hi guys, I am really interested in your products (and mainly in this Pixhawk Kit) but I will be charger with imports fees here in Netherlands. Is there shop on this side of the Atlantic where I can buy from? Thanks for all

Was this review helpful to you?